yyyyyy x. yyyyyy                                                    0000 xxxxxx xxxx , xxxx , xxxxx 00000

                                                                                                                                                  xxx-xxx-xxxx

abc@xyz.com

 

objective

proficient engineering professional eager to contribute advanced education, evaluation, research, project management and support expertise in a challenging microelectrical and opto-electrical engineering assignment.

 

career profile

ø  over five years of microelectrical and opto-electrical engineering experience.

ø  phd, master of science and bachelor of science degrees in electrical engineering.

ø  outstanding capacity to provide leadership in technical team environments.

ø  well-organized multi-tasker with strong detail orientation and departmental coordination abilities.

ø  adept in aligning engineering contributions with organizational objectives.

ø  well-versed in equipment maintenance, troubleshooting and repair.

ø  skilled consultant and advisor to clients and senior management.

ø  engineering and manufacturing trainer and certifier.

ø  proficient in process control matching metrics.

ø  oversee effective design and manufacture of reactors, ovens, evaporators and photolithography.

 

professional experience

intel corporation (300mm hvm), rio rancho, nm                                                                         2005 - present

acting area group leader (2010 c present)

       promoted to oversee five process engineers and eight non-exempt manufacturing technicians in low-k interlayer dielectric module.

       increased tool availability from 70% to 84% and report to management on process control matching, commodity cost spending, availability and cycle time.

 

senior process engineer (2005 c 2010)

       retained to support round-the-clock engineering and single point-of-contact for low-k interlayer dielectric module.

       monitored and identified ild tool issues, maintained low numbers of defects and drove escalation plans.

       led weekly process control reviews, reported results and improved quality by addressing mismatches.

       reported to factory-level forum to communicate process matching between new mexico and other sites.

       coordinated with integration, etch and litho engineers to develop comprehensive qualification plan.

       tested wafer parameter matching, performed sims analysis for film compositional matching, integrated short loop ild adhesion testing, processed lots and implemented pilot program of 40 lots.

       implemented model to predict product deposition rates and trained new engineers on process controls.

       trained and certified level i & ii manufacturing technicians on operations and processes.

       conducted advanced process training for engineering and manufacturing departments.

       module team leader for transfer and start up of intel 45nm ild process.

       represented new mexico in companywide ild forums.

       provided leadership for module business and start up process.

 

education

university of connecticut, storrs, ct

doctorate of philosophy, electrical engineering 2006

master of science, electrical engineering 2001

bachelor of science, electrical engineering 1998

yyyyyy x. yyyyyy

page two

 

academic experience

university of connecticut ece department, storrs, ct                                                                      1998 - 2005

research assistant (1998 c 2005)

       supported design/assemble of photoassisted microwave plasma, high-vacuum organic mocvd, ge vpe and sige movpe reactors.

       maintained production-line emcore movpe reactor, physical evaporation stations, high-temperature ovens, photolithography stations, plasma asher, rie station, alphas step and cvc rf sputtering system.

       implemented device fabrication of znse and zns-based material systems on iii-iv and iv substrates, x-ray diffraction techniques and characterization of ii-vi semiconductor material grown in emcore reactor.

       ordered parts and equipment and assisted graduate students.

 

teaching assistant (2005 c 1998)

       introduced embedded microcontrollers into course structure, developed new laboratory experiments and corrected post-laboratory reports in ece 266 microprocessor/ece 268 mircro/optics/ee 261 and ee291 senior design laboratories.

       assisted students in designing and processing diodes, solar cells, mos capacitors, bjts and scrs.

       maintained and managed processing equipment and corrected pre- and post-laboratory reports.

 

publications and conferences

characterization of cladding and core strain and thicknesses in zncdse-znse cladded quantum dots using wide-angle x-ray diffraction and pl data, cmoc 2007

zncdse-znse cladded quantum dots using photoassisted microwave plasma (pmp) enhanced metalorganic chemical vapor deposition for lasers and electroluminescent phosphors, nsti and osa 2006

ge epitaxy growth and characterization, cmoc 2005

fabrication of si/siox nanoparticles, cmoc 2005

compositional control and structural properties of znse1-x tex epitaxial films on lattice matched ingaas/inp (001) by photoassisted metal organic vapor phase epitaxy, mrs 2004

the photoassisted movpe growth of znse(n)/gaas(p+) solar cells, cmoc 2000, solid state electronics 2003

patterned heteroepitaxial processing applied to zns and zns.02se.98 on gaas (001), jap 2002

complete removal of threading dislocations from mismatched layers by patterned heteroepitaxial proccessing, apl 2000, 2000 ii-vi conference, jem 200, cmoc 2001

efficient doping of nitrogen into znse using tba and a /high-intensity uv source, cmoc 200

the photoassisted movpe growth of znse using t-bush, 1999 ii-vi conference, jem 2000

x-ray rocking curve analysis of tetragonally-distorted ternary semiconductors on mismatched (001) substrates, journal of vacuum science and technology 1999

 

 

 

 

 

 

 

 

yyyyyy x. yyyyyy                                                    0000 xxxxxx xxxx , xxxx , xxxxx 00000

                                                                                                                                                  xxx-xxx-xxxx

abc@xyz.com

 

 

cover letter text

 

date

 

 

 

hiring agent name

title

company name

address

city, state   zip code

 

dear                   :

 

i am currently seeking a challenging career opportunity in a microelectrical and opto-electrical engineering capacity and am submitting my resume for your review.  in advance, i thank you for your time and consideration. as demonstrated in the accompanying resume, my professional qualifications include a phd, master of science and bachelor of science degrees in electrical engineering and over five years of evaluation, research, project management and support experience. to complement this background, i possess staff management, analytical and problem-solving capabilities. as an employee, you will find me to be an enthusiastic and disciplined team player, committed to supporting you in achieving your objectives through superior performance. 

 

i am confident that i could be a valuable asset to your firm, and look forward to interviewing with you in the near future to further discuss my areas of experience and expertise that would be a contribution to your organization.

 

 

 

 

sincerely,

 

 

 

yyyyyy x. yyyyyy

 

 

 

 

 

attachment